Ventilation & Heating

Moving, removing and regassing a heat pump: costs and rules

The Conduction Company on moving, removing and regassing a heat pump in Auckland: what each job costs, who may do it, the refrigerant rules and the wall.

Moving, removing and regassing a heat pump in Auckland is work The Conduction Company does alongside its heat pump and air conditioning installation. Moving or removing one is electrical work and refrigerant work at once. A move can be as small as shifting the indoor unit on a back-to-back install, or as big as taking the whole machine to another room with new pipe, wiring and ducting.

The Conduction Company prices each heat pump move, removal and regas after seeing the installation. It pumps the refrigerant down and recovers it, and never lets it out. The Conduction Company usually tops up an R32 unit with a slow leak, but often recommends replacing an older R410A unit.

What does it cost to move a heat pump to another wall?

The Conduction Company prices each heat pump move after an assessment, because what moves, and how far, sets the cost.

We quote on facts, not guesses

Before we give you a price, we carry out a proper assessment of your property and how you'll use your heat pump.
That way you know exactly what you're buying and the total cost, with no surprises.
Clear expectations from the outset, start to finish.

The estimates below are for standard heat pump moves.
The Conduction Company confirms final pricing after a property assessment.

Moving a heat pump with The Conduction Company usually costs $600 to $2,100 including GST. A typical move is around $1,000 including GST. Those figures come from seven heat pump moves The Conduction Company has completed and invoiced.

Where a move sits in that range depends on what moves. Moving only the outdoor unit a short way sits at the lower end for The Conduction Company's clients. Moving the whole system, indoor and outdoor, say from a lounge into a bedroom, sits towards the top: it needs new wiring, new footing for the outdoor unit, and new ducting (the plastic cover over the pipes) and capping. Moving only the indoor unit, with the outdoor unit staying put, also usually costs less than a whole-system move.

Distance matters as much. A back-to-back heat pump, with the outdoor unit straight through the wall behind the indoor unit and within about 3 metres of pipe, is much quicker to move. Take the indoor unit to a partition wall further away and The Conduction Company has to run new pipe and ducting between the two, which adds labour and materials.

"It's all very variable, depending on the exact installation," says Jordan Statham, director of The Conduction Company and a registered electrician and electrical inspector. "So we'd come and assess it first before giving a price."

Does a heat pump need a disconnect switch?

Yes. The Wiring Rules, AS/NZS 3000, require a heat pump with a compressor to have a lockable isolating switch "adjacent to but not on the unit". So when The Conduction Company moves an outdoor unit, the switch has to end up beside its new spot, which makes the move electrical work as well as refrigerant work.

What does it cost to remove and dispose of an old heat pump?

Most of the cost of removing an old heat pump is time, The Conduction Company finds, because the scrap metal and the recovered gas earn back very little.

The estimates below are for standard heat pump removal and disposal.
The Conduction Company confirms final pricing after a property assessment.

Removing and disposing of a heat pump with The Conduction Company costs about $400 including GST for a dedicated removal. That is in line with The Conduction Company's own past removal jobs. Where The Conduction Company is replacing the old unit, removal is included in the replacement price.

On site, removing a heat pump or air conditioner takes The Conduction Company about an hour to an hour and a half, Jordan Statham estimates. The first 15 to 20 minutes is pumping it down, which stores the refrigerant inside the outdoor unit. Then the team disconnects the indoor and outdoor units, removes the piping and ducting, and takes everything down, ready to go.

The unit goes back to The Conduction Company's workshop, where the refrigerant is emptied out with a recovery machine, "essentially just a big motor with valves", as Jordan Statham puts it. The gas goes into storage bottles, which are sold to a company that reuses it, and the metal goes to the scrap yard.

"The refrigerant cost that we get and the small amount that we get from the scrap metal doesn't cover the transportation cost or the time spent to remove the refrigerant," says Jordan Statham of The Conduction Company.

Recovering refrigerant into a cylinder needs an approved filler under the Health and Safety at Work (Hazardous Substances) Regulations 2017. Jordan Statham holds a Refrigerant License New Zealand licence in the Approved Filler category, endorsed for flammable gases, and The Conduction Company owns its own recovery gear.

Letting the gas out instead is an offence. The Ozone Layer Protection Act 1996 makes it an offence to knowingly, or without lawful excuse, release a controlled substance while installing, servicing or dismantling air conditioning. Heat pump refrigerants count, and the fine is up to $10,000. "It should be done properly, both for the benefit of the environment and for worker safety," says Jordan Statham of The Conduction Company.

What does a regas cost, and when is it not worth it?

The Conduction Company charges a heat pump regas by the 100 grams of refrigerant lost, plus labour. So the price depends on how much gas has gone, and which gas the unit uses.

The estimates below are for standard heat pump regassing.
The Conduction Company confirms final pricing after a property assessment.

The Conduction Company's refrigerant rates, the same it charges for heat pump repairs in Auckland:
R32: $26.22 including GST per 100 g, plus labour
R410A: $46.58 including GST per 100 g, plus labour

R32 is the most common refrigerant in modern heat pumps, and The Conduction Company finds it relatively low cost, because it is produced in bulk. When a slow leak over time is the only fault in an R32 unit, The Conduction Company will recommend a top-up. "You could get multiple more years out of it," Jordan Statham says.

R410A is the gas in older machines, and most R410A units The Conduction Company sees are past the six or seven year mark and out of warranty. It is also far dearer to top up. The cause is not a tariff. R410A is a strong greenhouse gas, so New Zealand puts a carbon price on it and caps how much can be imported. The Ministry for the Environment publishes a yearly levy on the gas inside imported equipment, a fair guide to that carbon cost. For 1 kg of R410A it was $41.55 in 2019 and is $113.99 in 2026, excluding GST.

So when an R410A unit is near the end of its life anyway, The Conduction Company will usually recommend replacing it rather than regassing it. It has happened before. A client wanted a top-up instead, and The Conduction Company did it. The machine was at the end of its life, so other parts soon started to fail and it had to be replaced anyway.

"Otherwise you'd just be throwing more money into a failing machine trying to keep it propped up," says Jordan Statham. Past the warranty, with other wear showing, The Conduction Company's advice is to bite the bullet and look at what a new heat pump costs to install in Auckland.

What must never be done when someone disconnects a heat pump themselves?

Never undo the pipes on a heat pump, and The Conduction Company advises against disconnecting one yourself at all. It is full of refrigerant under pressure, and that gas is a hazard to you and to the environment.

Escaping refrigerant can cause freezer burn. When a line breaks or a nut is undone, the gas rushes out and can freeze over the copper pipes. "We've certainly had blisters on our fingers before from gas escaping these machines," says Jordan Statham of The Conduction Company, describing broken units the team was repairing when a seal let go.

Modern refrigerant can also burn. R32, the usual gas in newer units, is rated A2L under AS/NZS ISO 817, the refrigerant safety standard, where the L stands for low burning velocity. "Mildly flammable" is fair, but it can burn, so The Conduction Company handles it as a flammable gas.

Letting that gas out while dismantling a heat pump is the offence described above. Pumping it down into the outdoor unit first, then recovering it, is how The Conduction Company takes one out.

The wiring has its own rules, which The Conduction Company's electricians take care of on a move or removal. Disconnecting a hard-wired heat pump from its power supply is prescribed electrical work under the Electricity (Safety) Regulations 2010, and the Electricity Act 1992 lets only authorised people do that work. The one exception is an owner who lives in the home. They may connect and disconnect fixed-wired appliances with the power off, following the homeowner code ECP 51 (section 79 of the Act and regulation 57). It does not cover a rental, and it covers the wires only.

Even where the law allows it, The Conduction Company recommends against it. The exemption does not let anyone release the refrigerant, and undoing the pipes without pumping the gas down first does exactly that. "Get a professional in to do it properly, for your own safety," Jordan Statham says.

Who patches the wall after a removal, and what does it look like?

The Conduction Company talks the wall through with you when it quotes the removal. For the inside wall, it can get its contractors in to patch, plaster, sand and paint the hole.

The outside wall is usually the dearer part, The Conduction Company finds. Render, or weatherboard cladding, can be hard to replace. So on a tight budget, The Conduction Company can leave the outside pipe hole in place, with its seal left on and the hole blocked up. You can deal with it later, for example when you next redecorate the outside of the house.

How the wall looks afterwards depends on what it is made of. Patching plasterboard inside is a fairly straightforward job, says Jordan Statham of The Conduction Company, while render and weatherboards outside are harder to replace.

In short

Moving or removing a heat pump is electrical work and refrigerant work together, and The Conduction Company prices each job after an assessment, from what Jordan Statham sees on its own Auckland jobs. The refrigerant is pumped down and recovered, because letting it out is an offence. A slow leak in an R32 unit is usually worth topping up, while an older R410A unit out of warranty is often better replaced. Jordan Statham is a registered electrician and electrical inspector, and holds a refrigerant licence.

Frequently asked questions

How much does aircon regas cost?

The Conduction Company charges an aircon or heat pump regas by the 100 grams of refrigerant lost, plus labour. That is $26.22 per 100 g for R32 and $46.58 for R410A, including GST. How much gas has gone, and which gas, sets the total.

Can you move a heat pump?

Yes. The Conduction Company moves the indoor unit, the outdoor unit or the whole system, pumping the refrigerant down into the outdoor unit first. Moving it further than a back-to-back install needs new pipe and ducting, so it costs more.

How do I disconnect my heat pump unit?

Leave it to a professional. Taking a heat pump off the wall starts with pumping the refrigerant down into the outdoor unit. The Conduction Company does that with its own refrigerant licence and recovery gear, and handles the electrical disconnection too.

How long does it take to change out a heat pump?

Taking the old unit out takes The Conduction Company about an hour to an hour and a half on site, including 15 to 20 minutes to pump the refrigerant down. How long the new unit takes to fit depends on the pipe run and where the units go.